If you want to access blazing-fast internet without a signal drop, then a Netgear router is the best device to configure. However, many users have reported that after performing Netgear router setup, when they try to log in to their device, they get welcomed by the 192.168.1.1 login not working error message.
To ensure that you don’t end up getting stuck with the 192.168.1.1 login error message, we’ve come up with this post. Here, you’ll find the best tips that’ll prevent you from getting a 192.168.1.1 login error message. Thus, without much delay, read on.
How to Fix 192.168.1.1 login Not Working Issue?
Fix 1: Check the Hardware
Let’s start with the basic fix first, shall we? If the hardware of your Netgear router is damaged or faulty, nothing can stop you from getting stuck with the 192.168.1.1 login not working issue. Thus, make sure that the hardware of your router isn’t damaged. In the event that the power cable has cut from any end, get it replaced right away. Also, make sure that your Netgear router is getting enough power supply from the wall socket.
Fix 2: Update the Internet Browser
One of the common yet major reasons why users face 192.168.1.1 login not working issue is because of an outdated web browser. Therefore, before performing Netgear 192.168.1.1 login, update your internet browser. For better performance, also clear its cache, cookies, and browsing history.
Fix 3: Have a Strong Internet Connection
You might know the fact that your WiFi-enabled devices start behaving weirdly because of a slow internet connection, right? The same is the case with 192.168.1.1 login. If you do not have a stronger internet connection then it will definitely stop you from accessing the 192.168.1.1 login page. Therefore, ensure that you have an active internet connection and your router is connected to the correct WiFi.
For a strong internet connection, it is recommended that you contact your service provider. Ask your ISP to put you on an upgraded internet plan. Also, ensure that your Netgear router and modem are well-connected via an internet connection.
Once you’re done with this fix, check your internet connection by accessing the router login page using 192.168.0.1 or 192.168.1.254 IP.
Fix 4: Perform Netgear Router Firmware Update
Your Netgear router needs a regular Netgear router firmware update to perform well. On the off chance if the firmware on your router is outdated, then it will not perform well. So, the next time you try to log in to your router using 192.168.0.1 or 192.168.1.254 IP, update its firmware first.
The instructions highlighted below will help you in updating your Netgear router:
- Power on your router and connect it to the existing modem.
- Switch on your PC or laptop and connect it to the router’s network.
- Launch an up-to-date internet browser.
- Enter 192.168.0.1 or 192.168.1.254 IP in the address bar.
- Follow the on-screen instructions.
By following the instructions in exact given order, you’ll be able to perform a Netgear router firmware update. Apart from that, you’ll also get a fix to the problem that might be stopping you from accessing the 192.168.1.1 login page.
Fix 5: Power Cycle Your Netgear Router
Did the aforementioned steps seem a little tricky to you? Don’t sweat over it! It’s high time that you power cycle or reboot your Netgear router. Rebooting your Netgear router regularly can fix many big technical issues with your device. Once you restart your Netgear device, check the internet connection by accessing the router login page using 192.168.0.1 or 192.168.1.254 IP.
The Bottom Line
So, this was all about the best troubleshooting tips to avoid getting stuck with 192.168.1.1 login not working issue. We hope this piece of writing helped you out of what and what not to do while accessing the 192.168.1.1 login page. Whatever is your feedback, feel free to share it with us through the comments section.
